DESIGN AND CONSTRUCT AN OPEN DIE FORGING MACHINE WITH A 1.5 HP ELECTRIC MOTOR AND 5 KG HAMMER

Armila Armila, M. Iqbal Darussalam, Rudi Kurniawan Arief

Sari


This project outlines the design and construction of an open forging machine equipped with a 1.5 HP electric motor and a 5 kg hammer for use in the Material Technology Laboratory. The primary objective was to create a versatile and controlled environment for forging and shaping materials. The project began with the conceptualization and design phase, where the layout and components of the machine were planned. Materials were carefully selected for durability and performance. Construction was meticulously carried out with an emphasis on safety.The machine underwent rigorous testing to ensure it met the laboratory's specific requirements, and adjustments were made for optimal performance. Fine-tuning was performed to calibrate the machine, addressing temperature control, speed, and pressure settings. The completed open forging machine promises to enhance research capabilities in material technology, facilitating experiments in material science and research. This project represents a significant step in advancing the laboratory's capabilities and marks the beginning of a new phase in material technology research and experimentation.

Keywords: Forging Machine, Electric Motor, Hammer, Material,Laboratory Equipment


Teks Lengkap:

PDF

Referensi


H. F. Putri, “Peningkatan Produktivitas Ukm Pande Besi,” vol. 8, no. April, pp. 47–52, 2020.

A. A. Nugroho, F. Rhohman, T. Mesin, F. Teknik, U. Nusantara, and P. Kediri, “Analisa Kebutuhan Daya Pada Mesin Pemarut Kelapa Kapasitas 20 Kg / Jam,” pp. 226–231, 2022.

Y. Fatullah, “Rancang Bangun Alat Mesin Tempa Pandai Besi Sistem Hammer Kapasitas 14 Kg,” J. Inovtek Seri Mesin, vol. Vol. 2, p. 35, 2022.

E. K. Mindarta et al., “Peningkatan kapasitas produksi melalui mesin tempa otomatis umkm pande besi desa sumberpasir,” no. 3, pp. 249–253, 2019.

E. Didik, M. Mardjuki, and J. Jumiadi, “Analisa Pengaruh Deformasi Plastis Terhadap Struktur Mikro Dan Kekerasan Pada Baja St 42,” Transmisi, vol. 11, no. 1, pp. 19–26, 2015, [Online]. Available: https://jurnal.unmer.ac.id/index.php/jtmt/article/view/4536

S. Darmanto, “Aplikasi Mesin Tempa Mini Di Industri Pande Besi,” J. Pengabdi. …, vol. 01, no. 03, pp. 187–190, 2020, [Online]. Available: https://ejournal2.undip.ac.id/index.php/jpv/article/view/7441

J. Gronbæk and T. Birker, “Innovations in cold forging die design,” Wire, vol. 49, no. 2, 1999.

A. Septiawan, M. Mukhnizar, and Z. Zulkarnain, “Pembuatan Mesin Tempa Logam Dengan System Forging Hammer,” J. Tek. Komputer, Agroteknologi Dan Sains, vol. 2, no. 1, pp. 1–8, 2023, doi: 10.56248/marostek.v2i1.41.

U. Popp and U. Engel, “Microtexturing of cold-forging tools - Influence on tool life,” Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., vol. 220, no. 1, pp. 27–33, 2006, doi: 10.1243/095440505X32968.

“The_state_of_the_art_in_cold_forging_lub (1).pdf.”




DOI: https://doi.org/10.31869/rtj.v7i1.4983

Article Metrics

Sari view : 58 times
PDF - 32 times

Refbacks

  • Saat ini tidak ada refbacks.


##submission.copyrightStatement##

"Web Kunjungan Saat ini

Kunjungan Dari Negara

 Flag Counter

 

 

Creative Commons License
Rang Teknik Journal is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.